How to Set up a Tub: Install an Acrylic Bathtub as Well as Tub Surround
How to Set up a Tub: Install an Acrylic Bathtub as Well as Tub Surround
Blog Article
Every person maintains their own unique idea involving Installing A Bathtub.
Installing a bathtub isn't specifically brain surgery, however it does require strong plumbing, woodworking, and sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately difficult job. If the old tub is readily obtainable, the task can move quickly; if you need to open a wall surface to get rid of the old bathtub as well as position the new bathtub, the job is a lot harder. In either situation, the job is within a home handyman's skills, although you will certainly require a helper to move out the old tub and also embeded in the new one. Ensure you have actually certified yourself for the job and also fit attempting it. Rather than hiring a service provider to take over a halfway-completed project, it is far better to take into consideration employing one before you start. Possibilities are you may require a professional plumber to make tube links.
This article will certainly help you mount a new bath tub in your restroom if you have actually already acquired a new bathtub as well as do not need to change the plan of your previous water supply pipes.
Your devices as well as product checklist need to make up the following:
Planning for the Installation
First of all, the sustaining framework provided with the bath needs to be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is important to see to it that if the tap features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets unit to prevent pressure on the bathtub.
Fit the adaptable tap ports to the bottom of both faucets using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom need to now be ready to be fitted in its final setting.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is disconnect the water supply. After doing so, turn on the taps to drain any type of water staying in the system. The procedure of eliminating the existing taps can be rather troublesome as a result of the limited accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the taps. Have a fabric prepared for the staying water that will come from the pipes. Once the supply pipes have been removed, use the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
Prior to going on to fit the new taps, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Installing the Bath tub
Making use of both wooden boards under its feet, place the bathtub in the called for setting. The wooden boards are useful in evenly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 little points.
The next objective is to make sure that the tub is leveled all round. This can be achieved by examining the level and adjusting the feet on the bath tub up until the spirit level reviews degree.
To install taps, fit all-time low of the furthest flexible faucet port to the appropriate supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Activate the water system and examine all joints as well as new pipework for leakages as well as tighten them if necessary. Load the bathtub as well as likewise check the overflow electrical outlet as well as the regular electrical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the supplier's user's manual. Tiling as well as sealing around the bathtub must wait up until the bathtub has actually been utilized at least when as this will resolve it right into its final placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end supplies a connection to the current supply pipes.
If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the mounting opening in the bath/basin ensuring that the washing machines remain in place between the tap as well as the sink. Secure the tap in position with the producer supplied backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former kind needs to be connected to the tap finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, causing the water to penetrate the wall in between the bathroom and the tiling, resulting in issues with moisture and also feasible leakages to the ceiling below.
You can choose from a range of coloured sealers to assimilate your components and fittings. They are sold in tubes as well as cartridges, as well as can securing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of drenched paper or soft rope. Keep in mind to always fill up the tub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealant can crack fairly very early if you do not think about this motion prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly offered on the marketplace. It is a good idea to fit the ceramic tiles utilizing waterproof or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that content on How to Install a Bathtub when surfing the search engines. Sharing is good. Helping others is fun. I enjoy reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Contact Us Today
Report this page